AutoLeveller updates

Help for setting up and using
daedelus
Site Admin
Posts: 387
Joined: Tue Oct 01, 2013 1:41 pm
Location: London, UK
Contact:

AutoLeveller updates

Post by daedelus »

Just added an update for AutoLeveller 0.7.7.

If the input gcode file does not state the units (G20/G21) then a dialog box asks the user to manually select either inches or millimeters.

Please download the latest if needed: http://www.autoleveller.co.uk/download/ and let me know if there are any major problems with it :)
http://www.autoleveller.co.uk/. Software to probe and adjust a GCode file for PCB's or any probe-able surface.

http://www.autoleveller.co.uk/cnc-probe-guide/. A short guide to setting up the probe.

-James
User avatar
Country_Bubba
Posts: 124
Joined: Wed Oct 02, 2013 3:07 pm
Location: LaGrange, GA USA
Contact:

Re: AutoLeveller updates

Post by Country_Bubba »

Seems to be working here running a quick test on a previously run gcode file. :D
Art
Country Bubba
daedelus
Site Admin
Posts: 387
Joined: Tue Oct 01, 2013 1:41 pm
Location: London, UK
Contact:

Re: AutoLeveller updates

Post by daedelus »

cheers Art. :)
http://www.autoleveller.co.uk/. Software to probe and adjust a GCode file for PCB's or any probe-able surface.

http://www.autoleveller.co.uk/cnc-probe-guide/. A short guide to setting up the probe.

-James
Hessel Oosten
Posts: 24
Joined: Sat Oct 12, 2013 8:36 pm

Re: AutoLeveller updates

Post by Hessel Oosten »

And "YES OK HERE" too, at the level of the problematic G-code-producer ....:-).

Thanks James,

Hessel
dfajardo
Posts: 4
Joined: Wed Jan 01, 2014 12:41 am

Re: AutoLeveller updates

Post by dfajardo »

Daedelus -
This is great software, just what I needed. Thanks!

Don't like to be the bearer of bad news, but there is a (hopefully small) problem with the website.

I was not able to download the current version of AutoLeveler from the website (from http://www.autoleveller.co.uk/, when I click on "Downloads" I get an "Archives" page with the message "It seems we can't find what your're looking for. Perhaps searching can help." and a search box. As a result, I am using version 0.7.4, which was the latest available from the website under "Previous Versions".

*** Doug F.
Doug Fajardo
User avatar
Country_Bubba
Posts: 124
Joined: Wed Oct 02, 2013 3:07 pm
Location: LaGrange, GA USA
Contact:

Re: AutoLeveller updates

Post by Country_Bubba »

Doug,
I also found the same problem as you stated.
However, I also typed in "down" without the quotes in the search box and scrolled down and it came up with links to the two types of 7.7 and clicking on that started a download.

Hope this helps as I am sure James is either partying hard (its after midnight over there) or in bed.

Good Luck

Art
Country Bubba
Art
Country Bubba
dfajardo
Posts: 4
Joined: Wed Jan 01, 2014 12:41 am

Re: AutoLeveller updates

Post by dfajardo »

Thanks Country-Bubba; I found the 0.7.7 version just as you indicated. Happy New Year to both you and to Jim !
Doug Fajardo
daedelus
Site Admin
Posts: 387
Joined: Tue Oct 01, 2013 1:41 pm
Location: London, UK
Contact:

Re: AutoLeveller updates

Post by daedelus »

I am still not sure what caused the problem but the downloads page should be fixed now. Let me know if not.
http://www.autoleveller.co.uk/. Software to probe and adjust a GCode file for PCB's or any probe-able surface.

http://www.autoleveller.co.uk/cnc-probe-guide/. A short guide to setting up the probe.

-James
User avatar
Country_Bubba
Posts: 124
Joined: Wed Oct 02, 2013 3:07 pm
Location: LaGrange, GA USA
Contact:

Re: AutoLeveller updates

Post by Country_Bubba »

Looks good on this end.
Art
Country Bubba
minitreintje
Posts: 9
Joined: Mon Dec 23, 2013 4:40 pm

Re: AutoLeveller updates

Post by minitreintje »

It's fixed! Thanks!

Dylan
Post Reply